Repairing Brush Roll Failure in Bissell CleanView Rewind 85

Introduction

The Bissell CleanView Rewind 85 is designed to keep your floors spotless, but like any machine that moves across carpet and tile, its brush roll can wear out over time. When the brush roll stops rotating or spins too slowly, the vacuum’s suction drops and the carpet looks uneven. Repairing a brush roll failure can be done at home with a few simple tools and a clear step‑by‑step approach. This guide walks you through every part of the process, from diagnosing the problem to reassembling the unit and preventing future failures.

Signs of Brush Roll Failure

• Reduced Suction: Floors feel drier and dust accumulates more quickly than usual.
• Uneven Cleaning: Streaks or patches remain after a sweep, especially on high‑traffic areas.
• Noise and Vibration: The brush roll sounds rattling, humming, or squealing when the vacuum is running.
• Visual Inspection: The roller wheel appears dull or its surface is worn, and you may notice missing or bent bristles.

If you notice any of these symptoms, it’s time to check the brush roll.

Tools Needed

• Flat‑head screwdriver
• Phillips‑head screwdriver
• Small Phillips‑head or flat‑head bit set (for removing screws and clip tabs)
• Pair of safety glasses
• Cloth or paper towels
• New brush roll (compatible with Bissell CleanView Rewind 85)

Safety Precautions

• Always unplug the vacuum from the outlet before opening or working on it.
• Put on safety glasses to protect your eyes from debris.
• Work on a flat, dry surface to prevent slipping.

Disassembly Process

1. Locate the Brush Roll Cover
   The brush roll is situated beneath the front of the vacuum. Slide the cover forward until it lifts and reveals the roller.

2. Remove the Brush Roll
   a. Hold the brush roll in one hand.
   b. With the other hand, use the screwdriver to release the retaining clip or screw that keeps the roller in place.
   c. Pull the brush roll straight out of its housing.
   d. If the roller is glued, gently pry it with a flat‑head screwdriver.

3. Extract the Brush Roll Housing
   a. Once the roller is out, the housing sits on the bottom.
   b. Remove the screws that secure the housing to the vacuum body.
   c. Carefully lift the housing out; you may find a small cleaning brush inside that also needs attention.

4. Take Down the Brush Roll Cover
   a. Unfasten any screws or clips holding the cover.
   b. Remove the cover to expose the brush roll and any related bearings.

Cleaning the Brush Roll

Before deciding to replace the roller, give it a thorough cleaning:

• Use a brush or comb to remove hair, string, and debris that may be wrapped around the bristles.
• Check the roller’s base for foreign objects or damage.
• If the roller has a rubber base, inspect for cracks or excessive wear.

Inspecting for Damage

• Physical Wear: Look for frayed, bent, or missing bristles.
• Structural Damage: The roller may be warped or have broken sections.
• Bearing Condition: If the roller spins on a bearing, check for oil leakage, rust, or foreign material inside the bearing chamber.

If the roller shows any of these issues, replacement is recommended.

Replacing the Brush Roll

1. Select the Correct Replacement
   Ensure you have a brush roll specifically made for the Bissell CleanView Rewind 85. Using an incorrect size or type can affect performance.

2. Install the New Roller
   a. Slide the new brush roll into the housing, aligning the mounting tabs or screw holes.
   b. Secure it with the retaining clip or screw, ensuring it is firmly in place.

3. Reassemble the Brush Roll Housing
   a. Place the housing back onto the vacuum body.
   b. Tighten all screws evenly to avoid wobbling.

4. Reattach the Brush Roll Cover
   a. Position the cover over the housing.
   b. Fasten it with screws or clips, making sure it sits snugly.

Reassembly

• Carefully put the brush roll back into the housing if you had removed it earlier.
• Ensure the roller spins freely when you manually rotate it.
• Replace the front cover and secure it with the latch or screws.

Testing

1. Plug In and Power On
   Turn on the vacuum and listen for the brush roll’s rotation.
2. Run a Test Sweep
   Move the vacuum across a carpeted area.
3. Check Suction and Cleaning Quality
   The floor should feel consistently cleaned and the vacuum should maintain steady suction.

If the vacuum still shows reduced suction or uneven cleaning, double‑check the assembly for any loose screws or misaligned components.

Maintenance Tips

• Regular Cleaning: Remove hair and debris from the brush roll and its housing at least once a month.
• Rotate the Brush Roll: When you use the vacuum, periodically stop and let the roller spin freely for a few seconds to prevent buildup.
• Inspect the Brush Roll: During each routine maintenance session, look for signs of wear and replace the roller before it fails completely.
• Keep the Vacuum Dry: Moisture can cause rust in the bearings; store the vacuum in a dry area.

Troubleshooting Common Issues

Conclusion

Repairing brush roll failure on a Bissell CleanView Rewind 85 doesn’t have to be daunting. By following the steps outlined above, you can extend the life of your vacuum, maintain optimal cleaning performance, and save money on replacement units. Regular maintenance is key—cleaning the brush roll and inspecting it for wear will keep your vacuum in top shape for years to come. Happy cleaning!