Samsung DWB60 Dryer Wont Start Step by Step Repair

Safety First

Before you open a dryer or touch any wiring, make sure the unit is disconnected from power.

• Unplug the dryer from the outlet or switch off the circuit breaker that supplies the dryer.
• If you are not comfortable with electrical work, call a licensed appliance technician.

What Might Cause a Samsung DWB60 to Stay Stuck in “Not Start” Mode?

A Samsung DWB60 that refuses to start can be the result of many different problems.

• A broken door latch or a mis‑aligned door that the safety interlock does not recognize.
• A faulty start button or control panel that does not register the command.
• A tripped thermal fuse or high temperature sensor that tells the unit “stop.”
• Power supply issues such as a blown outlet or a defective wall plug.
• A jammed drum or a blocked vent that triggers an overload protection.

Below is a step‑by‑step guide that will help you narrow down the cause and, in many cases, repair the dryer yourself.

Step 1: Confirm the Dryer Is Receiving Power

1. Check the outlet

   • Plug in another appliance to see if the outlet is active.
   • Use a voltage tester or a multimeter to verify 120 V AC.

2. Inspect the power cord

   • Look for frayed or exposed insulation.
   • If the cord appears damaged, replace it before proceeding.

3. Reset the dryer’s internal fuse

   • Some Samsung models have a reset button on the control panel. Press it and see if the dryer powers up.

If the dryer still does not power on, the problem likely lies in the unit’s internal electronics or safety mechanisms.

Step 2: Verify the Door Latch and Safety Interlock

The dryer will not start unless the door latch is engaged properly.

1. Open the door and locate the latch

   • The latch is usually a metal bar that slides into a catch on the side of the cabinet.

2. Test the latch manually

   • With the dryer unplugged, press the latch to ensure it moves freely.
   • Look for any bent or broken pins.

3. Check the interlock switch

   • The switch sits in the door frame and sends a signal to the control board.
   • Use a multimeter on continuity mode to confirm the switch is functioning.
   • If the switch is open (no continuity), replace it.

4. Re‑engage the latch

   • Close the door firmly and listen for the click that indicates the latch is secure.

If the dryer starts after the latch is secure, the interlock was the issue.

Step 3: Inspect the Control Panel and Start Button

Samsung dryers use a touch‑pad or button‑style control panel.

1. Look for physical damage

   • Check for cracked pads, stuck buttons, or a wet surface that could cause a short.

2. Test the start button

   • With the dryer unplugged, press the start button and listen for a click.
   • If there is no sound, the button may be faulty.

3. Check the panel’s wiring

   • Remove the panel cover (usually held by two screws).
   • Inspect the ribbon cable for cuts or loose connections.

4. Test continuity between the start button and the control board

   • Use a multimeter to confirm a closed circuit when the button is pressed.

5. Replace components as needed

   • A defective start button can usually be swapped for a new part from a Samsung parts supplier.

After confirming the panel works, proceed to the next step.

Step 4: Examine the Thermal Fuse and Temperature Sensor

The dryer’s safety system will shut down if it detects overheating.

1. Locate the thermal fuse

   • On the Samsung DWB60 it is typically near the blower or at the back of the dryer cabinet.
   • It looks like a small rectangular metal box with a wire lead.

2. Test the fuse

   • Remove the fuse and test it with a multimeter for continuity.
   • A blown fuse will show an open circuit.

3. Check the temperature sensor

   • The sensor is a small black or white probe with a wire.
   • Test it for continuity; it should read a consistent resistance.

4. Replace if necessary

   • Buy a new thermal fuse or sensor that matches the model’s specifications.
   • Install the new part and reset the dryer’s internal fuse.

A blown thermal fuse often points to a vent blockage or an overworked motor, so address those issues next.

Step 5: Assess the Venting System

Ventilation problems can trigger the dryer’s overload protection and prevent it from starting.

1. Check the external vent

   • Open the vent hood on the back of the dryer.
   • Ensure the hose is free of kinks and that the exhaust fan is not blocked.

2. Inspect the ductwork

   • Pull the duct out of the wall and look for lint buildup.
   • Clean or replace the duct if it is clogged.

3. Test the drum and motor

   • Manually spin the drum to ensure it turns freely.
   • If the drum is jammed, clean out any foreign objects.

4. Clear lint from the lint filter

   • The lint filter is usually on the front of the dryer or near the door.
   • A clogged filter can cause overheating.

Once the venting is clear, try starting the dryer again.

Step 6: Reset the Dryer’s Control Board

If all hardware appears sound, the issue may lie with the electronic control board.

1. Power cycle the dryer

   • Unplug the dryer for at least five minutes.
   • Plug it back in and wait for the control panel to reset.

2. Run a diagnostic cycle (if your model supports it)

   • Press and hold the “Start” button for several seconds to trigger a self‑test.
   • Observe any error codes that appear on the display.

3. Consult the error code list

   • Samsung error codes are typically printed in the user manual or on the control panel.
   • Codes such as “E07” or “E08” often refer to door latch or start button faults.

4. Replace or re‑program the control board

   • If the diagnostic cycle indicates a board fault, contact Samsung service or purchase a replacement board.
   • Reprogramming a control board usually requires specialized equipment, so professional service may be necessary.

Step 7: Final Check and Restart

After addressing the likely causes, perform a final review.

• Verify all connections are secure.
• Ensure the door latch is engaged.
• Confirm the vent system is clear.
• Plug the dryer back in and attempt to start it.

If the dryer starts, you have successfully repaired the unit.

When to Call a Professional

Some situations are beyond DIY repair or require specialized tools.

• Complex electrical faults on the control board.
• Faults involving high voltage components.
• Problems that persist after all checks.

Calling a licensed technician will prevent damage to the dryer and keep you safe.

Prevention Tips to Keep Your Samsung DWB60 Running Smoothly

• Clean the lint filter after every load.
• Inspect the vent regularly for clogs.
• Check the door latch annually for wear.
• Run the dryer on the “auto” cycle to allow the thermostat to regulate temperature.
• Avoid overloading the dryer; a full drum can cause overheating.

Recap of Key Diagnostics

Following the steps above should resolve the most common issues that cause a Samsung DWB60 dryer not to start. Always prioritize safety, and when in doubt, seek professional assistance.